Technical
Support
View
the most commonly asked questions. |
|
|
|
What's
New?
We are working to improve this website and service to our exisiting customers.
Our new contact details are here
|
|
 |
|
 |
|
|
|
 |
|
 |
|
|
|
 |
|
 |
|
 |
|
|
|
|
|
|
|
|
|
|
|
Dear valued customers,
Please note that Spatter Shield is under new management and we ask that you be patient while we work on the website and follow up any queries.
I can be contacted on Email and will reply to all questions.
I look forward to re-establishing our business relationships.
Best Regards,
Managing Director,
Spatter Shield Australia.
• All new contact details here •
|
|
Do you have Anti Spatter Problems with your Manual, Semi Automatic or Robotic Welder?
The Spatter Shield™ anti spatter welding accessory inline anti-spatter system is a LOW COST & a technical advancement for both Manual, Semi Automatic and Robotic MIG Welders. The Spatter Shield™ anti spatter welding accessory kit will reduce the need for hand sprays, reduce machinery downtime and significantly reduce the adhesion of spatter build up around the gas shroud and weld site. Suits all Manual Welders such as Miller, Lincoln, ESAB, Fronius and Kemppi.
Being such a LOW COST item you could almost fit a Spatter Shield Probe & Canister on each Manual or Robotic Welder.
Suits Welding Robots such as Lincoln, Fronius & Motoman.
|
|
Read What Our
Customers Have to Say
Real Life Case Study #1
We can hereby confirm that the Spatter Shield™ systems employed on our
Robotic welding systems are proving to be both efficient and cost
effective. The life of the consumable parts i.e. Gas Shrouds, Contact
Tips, Tip Holders and Gas Diffusers are showing at least 4 times the
life than was previously experienced. We are not using any Mechanical
Cleaning Device either.
~
KHK Scaffolding & Formwork LLC
Real
Life Case Study #2
Further to our recent conversation, I can confirm we clean the nozzle
on our robotic welding system twice per shift. The spatter removal
is easily achieved by manual means, we do not have within our welding
cell any mechanical torch cleaning devices, the Spatter Shield™ system
fitted works perfectly well and provides protection to both nozzle and
gas shroud. The spatter-shield system fitted to our robot has been
in operation for eight months.
~ Big Bear Products Limited
>>
Read more success stories |
Manual, Semi
Automatic and Robotic Welding
As can be seen from the
above pictures, the Spatter Shield Probe and Canister Kit can be
easily installed on Manual, Semi Automatic and Robotic MIG Welders.
Suits Welding Robots
such as Lincoln, ESAB & Motoman.
How to install the
Spatter Shield Probe & Canister Kit.
The installation of the Spatter Shield
Inline Anti Spatter System should NOT be installed before the solenoid.
This applies to Manual, Semi Automatic and Robotic MIG Welding.
The correct installation of the Spatter
Shield Inline Anti Spatter System should ALWAYS occur after the
solenoid. This applies for all Manual, Semi Automatic and Robotic
Welders
>> Click here to see
the full product range |
|
|
Application Features
- Gives a virtual spatter free weld gun nozzle;
- Continually lubricates the welding wire liner;
- Increases the life of the contact tip;
- Will not interfere with the formation of the
weld;
- Can be used with CO2 or various shielding gases
without affecting spray transfer or deposition rates
in GMAW and FCAW of steels;
- Promote higher productivity
- Contains NO SILICONE
- Easy to paint over
- Low cost and easy set up.
>>
Read more success stories |
|
|
Example of
Welded Parts
Using Spatter Shield
Anti Spatter Kit
|
|
Car Body
Trolley Jack
Spade
Air Compressor
|
|
Types of Industries that use
the Spatter Shield In Line Anti Spatter System. |
|
>>
Would you like to view the
REAL LIFE CASE STUDIES
in full.
The Works Work Anti Spatter Product Range available.
>> Click here |
|
|
|
